Order hotline: (386) 774-7785

The World’s Leading Device Programmers

My Shopping Cart

0 Items

Dataman 848Pro2 Super Fast Stand-Alone Programmer

Quick Overview

Super fast universal stand-alone gang programmer with eight independent 48-pin ZIF sockets and internal control PC driven by Windows Embedded 8.1 Industry Pro. Concurrent programming options combine with device insertion tests and a user friendly interface to give higher programming yields and reduced failure rates.


The 848Pro2 is built to meet the demands of high volume production programming with minimal operator effort.

Be the first to review this product

Availability: In stock

$8,995.00
OR
Dataman 848Pro2 Super Fast Stand-Alone Programmer

Double click on above image to view full picture

Zoom Out
Zoom In

Details

General

  • 848Pro2 programmer offers the same advanced features as 848Pro programmer but with much higher programming speeds (20-75%) for high-capacity memories.
  • Independent programming is more efficient than the concurrent programming method used in traditional gang programmers as each site operates independently allowing programming to start as soon as each device is inserted into the ZIF socket. Before the last device is loaded, the first device is already programmed and ready for removal. The operator is always busy removing and inserting chips, so both the operator and programmer are running continuously at maximum efficiency. With traditional gang programmer operation, the operator is idle while chips are being programmed and the programmer is idle while chips are being removed and new chips inserted. Therefore for the medium programming times, you can easily achieve the throughput of a larger gang programmer with one 848Pro2 programmer.
  • FPGA based totally reconfigurable 48 powerful TTL pindrivers provide H/L/pull_up/pull_down and read capability for each pin of socket. Advanced pindrivers incorporate high-quality high-speed circuitry to deliver signals without overshoot or ground bounce for all supported devices. Pin drivers operate down to 1.8V so you'll be ready to program the full range of tomorrows advanced low-voltage devices.
  • Each programming module performs device insertion and contact tests before programming each device. These capabilities, supported by overcurrent protection and signature-byte check help prevent chip damage due to operator error.
  • The selftest capability allows diagnostics included in the software to thoroughly check the health of each programming module.
  • Built-in protection circuits eliminate damage to programming modules and/or programmed devices due to environment or operator failure. All ZIF sockets and ISP connector pins are protected against ESD up to 15kV.
  • 848Pro2 programmer performs programming verification at the marginal level of supply voltage, improving programming yield and guarantying long data retention.
  • Various socket converters are available to handle devices in PLCC, SOIC, PSOP, SSOP, TSOP, TSSOP, TQFP, QFN (MLF), SDIP, BGA and other packages.


Programmer Specification

  • 8 x universal programming modules (8 x 48-pin DIL ZIF sockets and 8 x ISP connectors)
  • Operation result LEDs, LED power indicator
  • Banana jack for ESD wrist strap connection
  • Banana jack for connection to ground


Module Specification

Base Unit (DAC)

  • On-board intelligence: powerful microprocessor and FPGA based state machine
  • Three D/A converters for VCCP, VPP1, and VPP2, controllable rise and fall time
  • VCCP range 0..8V/1A
  • VPP1, VPP2 range 0..26V/1A
  • Selftest capability


ZIF Socket

  • 48-pin DIL ZIF socket accepts both 300/600 mil devices up to 48-pin
  • Pindrivers: 48 universal
  • VCCP/VPP1/VPP2 can be connected to each pin
  • Perfect ground for each pin
  • FPGA based TTL driver provides H, L, CLK, pull-up, pull-down on all pindriver pins
  • Analog pindriver output level selectable from 1.8V up to 26V
  • Current limitation, overcurrent shutdown, power failure shutdown
  • ESD protection on each pin of socket (IEC1000-4-2: 15kV air, 8kV contact)
  • Continuity test: each pin is tested before every programming operation


ISP Connector

  • 20-pin male type with missinsertion lock
  • 6 TTL pindrivers, provides H, L, CLK, pull-up, pull-down; level H selectable from 1.8V up to 5V to handle all (including low-voltage) devices
  • 1x VCCP voltage (range 2V..7V/100mA), can be applied to two pins
  • Programmed chip voltage (VCCP) with both source/sink capability and voltage sense
  • 1x VPP voltage (range 2V..25V/50mA), can be applied to six pins
  • Target system supply voltage (range 2V..6V/250mA)
  • ESD protection on each pin of ISP connector (IEC1000-4-2: 15kV air, 8kV contact)
  • Two output signals, which indicate state of work result = LED OK and LED Error (active level: min 1.8V)
  • Input signal, switch YES! equivalent (active level: max. 0.8V)

User Interface

There are two ways to control and monitor the programming flow of the 848Pro2 stand-alone multiprogrammer: using the control unit or using a standard display, keyboard and mouse.

  • The graphical control unit with touch screen provides essential information about the programming flow and allows basic control of the 848Pro2 programmer.
  • Using a display, keyboard and mouse allows access to all programming flow information and options.


Production Mode Control

  • This part of the software is focused to the easy monitoring of high-volume production operations.
  • Operator-friendly control software combines many powerful functions with ease of use. Graphic user interface provides an overview of important information, reducing the burden on the operator with unnecessary details.
  • Project files are used to control the 848Pro2 and contain user data, chip programming setup, chip configuration, auto programming command sequence, etc. This helps minimize operator error as the project file is normally created and proofed by an engineer and then passed to the operator. The optional protected mode can be set avoiding unwanted changes to the project file.
  • Each chip may be programmed with different data such as serial number, configuration and calibration information.


Engineering Mode Control

  • This part of the software is focused to the quick and easy preparation of the project file for usage in the production mode control software.
  • Each programming module is driven by an easy-to-use control program with pull-down menus, hot keys and on-line help. Selecting of device is performed by its class, by manufacturer or simply by typing a fragment of vendor name and/or part number.
  • Standard device-related commands (read, blank check, program, verify, erase) are enhanced by test functions (insertion test, connection check, signature-byte check) and additional special functions (auto-increment, production mode - programming starts immediately once chip inserted into socket).
  • All known data formats are supported. Automatic file format detection and conversion during loading of file. Jam file (JEDEC standard JESD-71) and VME file compatible.
  • The versatile auto-increment function allows each programmed device to be assigned an individual or incrementing serial number. This function also enables the operator to read serial numbers or device identification signatures from a file.
  • The software provides extensive information about programmable devices including detailed drawings of all available packages. The software also provides explanations of chip labelling (prefixes and suffixes) for each of the supported chips.
  • Keeping your programmer software up to date can be a costly business with some programmers. Dataman offers completely FREE software updates whenever you need them. The latest software is always available from our website.


Device Support

The Dataman 848Pro2 supports over 105,000 of the most popular devices in use today - with future devices being added monthly. Dataman 848Pro2 coverage includes the following device types:

ZIF Socket

  • NAND Flash: Samsung K9xxx, KFxxx, SK Hynix (ex Hynix) HY27xxx, H27xxx, Toshiba TC58xxx, TH58xxx, Micron MT29Fxxx, (ex Numonyx ex STM) NANDxxx, Spansion S30Mxxx, S34xxx, 3D-Plus 3DFNxxx, ATO Solution AFNDxxx, Fidelix FMNDxxx, Eon Silicon Sol. EN27xxx, ESMT F59xxx, LBA-NAND Toshiba THGVNxxx
  • Serial NAND Flash: Micron MT29Fxxx, GigaDevice GD5Fxxx
  • eMMC: Hynix H26Mxxxxxxxx, Kingston KE44B-xxxx/xxx, Micron MTFCxxxxxx, Numonyx NANDxxxxxxxx, Phison PSM4A11-xx, Samsung KLMxxxxxxx, SanDisk SDINxxx-xx, Toshiba THGBMxxxxxxxxxx
  • Multi-chip devices: NAND+RAM, NOR+RAM, NOR+NOR+RAM, NAND+NOR+RAM
  • Serial Flash: standard SPI, high performance Dual I/O SPI and Quad I/O SPI (25Bxxx, 25Dxxx, 25Exxx, 25Fxxx, 25Lxxx, 25Mxxx, 25Pxxx, 25Qxxx, 25Sxxx, 25Txxx, 25Uxxx, 25Vxxx, 25Wxxx, 25Xxxx, 26Vxxx, 45PExx, MX66Lxxx, S70FLxxx), DataFlash (AT45Dxxx, AT26Dxxx)
  • Parallel NOR Flash: 28Fxxx, 29Cxxx, 29Fxxx, 29BVxxx, 29LVxxx, 29Wxxx, 49Fxxx series, Samsung's K8Fxxxx, K8Cxxxx, K8Sxxxx, K8Pxxxx series, ...
  • EPROM: NMOS/CMOS, 27xxx and 27Cxxx series
  • EEPROM: NMOS/CMOS, 28xxx, 28Cxxx, 27EExxx series, 3D Plus 3DEExxxxxxxx
  • mDOC H3: SanDisk (ex M-Systems) SDED5xxx, SDED7xxx, MD2533xxx, MD2534xxx, Hynix HY23xxx
  • FRAM: Ramtron
  • MRAM: Everspin MRxxxxx8x, 3D Plus 3DMRxxxxxxxx
  • NV RAM: Dallas DSxxx, SGS/Inmos MKxxx, SIMTEK STKxxx, XICOR 2xxx, ZMD U63x series
  • Serial E(E)PROM: 11LCxxx, 24Cxxx, 24Fxxx, 25Cxxx, 30TSExxx, 34Cxxx, 34TSxx, 59Cxxx, 85xxx, 93Cxxx, NVM3060, MDAxxx series, full support for LV series, AT88SCxxx
  • Serial FRAM: Cypress(Ramtron): FM24xxxxxx, FM25xxxxxx, Fujitsu: MB85RCxxxx, MB85RSxxxx, Lapis(OKI, Rohm): MR44xxxxx, MR45xxxxx
  • Serial MRAM: Everspin MH20xxx, MH25xxx
  • Configuration (EE)PROM: XCFxxx, XC17xxxx, XC18Vxxx, EPCxxx, EPCSxxx, AT17xxx, AT18Fxxx, 37LVxx
  • 1-Wire E(E)PROM: DS1xxx, DS2xxx
  • PLD Altera: MAX 3000A, MAX 7000A, MAX 7000B, MAX 7000S, MAX7000AE, MAX II/G/Z, MAX V
  • PLD Lattice: ispGAL22V10x, ispLSI1xxx, ispLSI1xxxEA, ispLSI2xxx, ispLSI2xxxA, ispLSI2xxxE, ispLSI2xxxV, ispLSI2xxxVE, ispLSI2xxxVL, LC4xxxB/C/V/ZC/ZE, M4-xx/xx, M4A3-xx/xx, M4A5-xx/xx, M4LV-xx/xx, ispCLOCK, Power Manager/II, ProcessorPM
  • PLD: Xilinx: XC9500, XC9500XL, XC9500XV, CoolRunner XPLA3, CoolRunner-II
  • SPLD/CPLD series: AMD, AMI, Atmel, Cypress, Gould, ICT, Lattice, National Semicond., Philips, STMicroelectronics, TI (TMS), Vantis, VLSI
  • FPGA: FPGA: Microsemi(Actel): ProASIC3, IGLOO, Fusion, ProASICplus, SmartFusion
  • FPGA: Lattice: MachXO, MachXO2, LatticeXP, LatticeXP2, ispXPGA
  • FPGA: Xilinx: Spartan-3AN
  • Clocks: TI(TMS), Cypress
  • Special chips: Atmel Tire Pressure Monitoring ATA6285N, ATA6286N; PWM controllers: Zilker Labs, Analog Devices; Multi-Phase ICs: IR(Chil Semiconductor); Gamma buffers: AUO, Maxim, TI, ...
  • Microcontrollers MCS51 series: 87Cxxx, 87LVxx, 89Cxxx, 89Sxxx, 89Fxxx, 89LVxxx, 89LSxxx, 89LPxxx, 89Exxx, 89Lxxx, all manufacturers, Philips LPC series
  • Microcontrollers Intel 196 series: 87C196 KB/KC/KD/KT/KR/...
  • Microcontrollers Atmel ARM. AT91SAM7Sxx, AT91SAM7Lxx, AT91SAM7Xxx, AT91SAM7XCxx, AT91SAM7SExx series;
  • Microcontrollers Atmel ARM9: AT91SAM9xxx series;
  • Microcontrollers ARM Cortex-M3: ATSAM3Axxx, ATSAM3Uxxx, ATSAM3Nxxx, ATSAM3Sxxx, ATSAMD20, ATSAM3Xxxx series
  • Microcontrollers ARM Cortex-M4: ATSAM4Sxxx series
  • Microcontrollers Atmel AVR 8bit/16bit: AT90Sxxxx, AT90pwm, AT90can, AT90usb, ATtiny, ATmega, ATxmega series
  • Microcontrollers Atmel AVR32: AT32UC3xxxx, ATUCxxxD3/D4/L3U/L4U series
  • Microcontrollers TI (Chipcon): CC11xx, CC24xx, CC25xx, CC85xx series
  • Microcontrollers Coreriver: Atom 1.0, MiDAS1.0, 1.1, 2.0, 2.1, 2.2, 3.0 series
  • Microcontrollers Cypress: CY7Cxxxxx, CY8Cxxxxx
  • Microcontrollers ELAN: EM78Pxxx
  • Microcontrollers EPSON: S1C17 series
  • Microcontrollers Explore Microelectronic: EPF01x, EPF02x series
  • Microcontrollers Generalplus: GPM8Fxxx series
  • Microcontrollers GreenPeak: GPxxx series
  • Microcontrollers Infineon(Siemens): XC800, C500, XC166, C166 series
  • Microcontrollers MDT 1xxx and 2xxx series
  • Microcontrollers Megawin: MG87xxx, MPC82xxx series
  • Microcontrollers Microchip PICmicro: PIC10xxx, PIC12xxx, PIC16xxx, PIC17Cxxx, PIC18xxx, PIC24xxx, dsPIC, PIC32xxx series
  • Microcontrollers Motorola/Freescale: HC05, HC08, HC11, HC12, HCS08, RS08, S12, S12X, MC56F, MCF51, MCF52 series, Kinetis (K,L), Qorivva/5xxx Power Architecture
  • Microcontrollers Myson MTV2xx, 3xx, 4xx, 5xx, CS89xx series
  • Microcontrollers National: COP8xxx series
  • Microcontrollers NEC: uPD70Fxxx, uPD78Fxxx series
  • Microcontrollers Novatek: NT68xxx series
  • Microcontrollers Nordic Semiconductor: nRF24LExxx, nRF24LUxxx, nRF315xx, nRF51xxx Flash and OTP series
  • Microcontrollers Nuvoton ARM Cortex-Mx: NUC1xx, M05x, Mini51, Nano1xx series
  • Microcontrollers Nuvoton (Winbond): N79xxx, W77xxx, W78xxx, W79xxx, W83xxx series
  • Microcontrollers NXP (Philips) ARM Cortex-Mx: LPC11xx, LPC11Cxx, LPC11Dxx, LPC11Uxx, LPC12xx, LPC12Dxx, LPC13xx, LPC17xx, LPC11Axx, LPC11Exx, LPC11xxLV, LPC18xx, LPC43xx, LPC8xx, EM7xx, series
  • Microcontrollers NXP (Philips) UOC series: UOCIII, UOC-TOP, UOC-Fighter (TDA1xxxx) series
  • Microcontrollers NXP (Philips) ARM7: LPC2xxx, MPT6xx, PCD807xx, SAF7780xxx series
  • Microcontrollers NXP (Philips) ARM9: LPC31xx series
  • Microcontrollers Pasat: TinyModule DIL40, DIL50 series
  • Microcontrollers Scenix (Ubicom): SXxxx series
  • Microcontrollers Syntek: STK6xxx series
  • Microcontrollers Renesas: R8C/Tiny series, uPD70Fxxx, uPD78Fxxx series, RL78 series, R32C series
  • Microcontrollers SyncMOS: SM39xxx, SM59xxx, SM73xxx, SM79xxx, SM89xxx series
  • Microcontrollers and Programmable System Memory STMicroelectronics: uPSD, PSD series
  • Microcontrollers STM (ex SGS-Thomson): ST6xx, ST7xx, ST10xx, STR7xx, STR9xx, STM32F/L/W, STM8A/S/L series, SPC5 (Power Architecture)
  • Microcontrollers Silicon Laboratories(Cygnal): C8051 series
  • Microcontrollers Silicon Laboratories(Energy Micro): EFM32Gxx, EFM32GGxx, EFM32LGxx, EFM32TGxx, EFM32WGxx series
  • Microcontrollers Silicon Laboratories: SiM3Cxxx, SiM3Lxxx, SiM3Uxxx series
  • Microcontrollers Texas Instruments: MSP430 series, MSC12xx series, TMS320F series, CC430 series,
  • Microcontrollers Texas Instruments (ex Luminary Micro): LM3Sxxx, LM3Sxxxx series, LM4Fxxxx series, TM4C series
  • Microcontrollers Zilog: Z86/Z89xxx and Z8Fxxxx, Z8FMCxxxxx, Z16Fxxxx, ZGP323xxxxxx, ZLF645xxxxxxx, ZLP12840xxxxx, ZLP323xxxxxxx series
  • Microcontrollers other: EM Microelectronic, Spansion(Fujitsu), Goal Semiconductor, Hitachi, Holtek, Novatek, Macronix, Princeton, Winbond, Samsung, Toshiba, Mitsubishi, Realtek, M-Square, ASP, Coreriver, Gencore, EXODUS Microelectronic, Topro, TinyARM, VersaChips, SunplusIT, M-Square, QIXIN, Signetic, Tekmos, Weltrend, Amic, Cyrod Technologies, Ember, Ramtron, Nordic Semiconductor, Samsung, ABOV Semiconductor...
  • EPROM: 2708
  • PLD: Bipolar PALxxx


ISP Connector

  • Serial E(E)PROM: IIC series, MW series, SPI series, KEELOQ series, PLD configuration memories, UN I/O series
  • 1-Wire E(E)PROM: DS1xxx, DS2xxx
  • Serial Flash: standard SPI (25xxx), DataFlash (AT45Dxxx, AT26Dxxx)
  • Serial FRAM: Cypress(Ramtron): FM24xxxxxx, FM25xxxxxx, Fujitsu: MB85RCxxxx, MB85RSxxxx, Lapis(OKI, Rohm): MR44xxxxx, MR45xxxxx
  • Microcontrollers Atmel: AT89Cxxx, AT89Sxxx, AT89LSxxx, AT89LPxxx, AT90pwm, AT90can, AT90usb, AT90Sxxxx, ATtiny, ATmega, ATxmega series
  • Microcontrollers Atmel AVR32: AT32UC3xxxx, ATUCxxxD3/D4/L3U/L4U series
  • Microcontrollers Atmel ARM7: AT91SAM7Sxx, AT91SAM7Xxx, AT91SAM7XCxx, AT91SAM7SExx series;
  • Microcontrollers TI (Chipcon): CC11xx, CC24xx, CC25xx, CC85xx series
  • Microcontrollers Cypress: CY8C2xxxx
  • Microcontrollers Elan: EM78Pxxx, EM6xxx series
  • Microcontrollers EM Microelectronic: 4 and 8 bit series
  • Microcontrollers Microchip PICmicro: PIC10xxx, PIC12xxx, PIC16xxx, PIC17xxx, PIC18xxx, PIC24xxx, dsPIC, PIC32xxx series
  • Microcontrollers Mitsubishi: M16C
  • Microcontrollers Motorola/Freescale: HC08 (both 5-wire, All-wire), HC11, HC12, HCS08, S12, S12X, MC56F, MCF52, Kinetis K series
  • Microcontrollers Nordic Semiconductor: nRF24LExxx, nRF24LUxxx, nRF315xx Flash and OTP series
  • Microcontrollers NXP (Philips) ARM7: LPC2xxx, MPT6xx series
  • Microcontrollers NXP (Philips) ARM Cortex-Mx: LPC11xx, LPC11Cxx, LPC11Dxx, LPC11Uxx, LPC12xx, LPC12Dxx, LPC13xx, LPC17xx, LPC11Axx, LPC11Exx, LPC11xxLV, LPC18xx, LPC43xx, LPC8xx, EM7xx, series
  • Microcontrollers NEC: uPD7xxx series
  • Microcontrollers Philips (NXP): LPCxx series, 89xxx series
  • Microcontrollers Renesas: R8C/Tiny series, uPD7xxx series
  • Microcontrollers Realtek, M-Square
  • Microcontrollers Samsung: ICPZBSxxx series
  • Microcontrollers Scenix (Ubicom): SXxxx series
  • Microcontrollers Silicon Laboratories(Energy Micro): EFM32Gxx, EFM32GGxx, EFM32LGxx, EFM32TGxx, EFM32WGxx series
  • Microcontrollers STM (ex SGS-Thomson): ST6xx, ST7xx, ST10xx, STR7xx, STR9xx, STM32F/L/W, STM8A/S/L series, SPC5 (Power Architecture)
  • Microcontrollers Silicon Laboratories(Cygnal): C8051 series
  • Microcontrollers and Programmable System Memory STMicroelectronics: uPSD, PSD series
  • Microcontrollers TI: MSP430 series (both JTAG and BSL), MSC12xxx series, CC430 series, LM4F series, TM4C series
  • Microcontrollers Zilog: Z8Fxxxx, Z8FMCxxxxx, Z16Fxxxx series, ZLF645x0xx
  • Various PLD (also by Jam/VME/SVF/STAPL/... Player/JTAG support):
  • Altera: MAX 3000A, MAX 7000A, MAX 7000B, MAX 7000S, MAX 9000, MAX II/G/Z, MAX V
  • Xilinx: XC9500, XC9500XL, XC9500XV, CoolRunner XPLA3, CoolRunner-II
  • PLD Lattice: ispGAL22xV10x, ispLSI1xxxEA, ispLSI2xxxE, ispLSI2xxxV, ispLSI2xxxVE, ispLSI2xxxVL, M4-xx/xx, M4LV-xx/xx, M4A3-xx/xx, M4A5-xx/xx, LC4xxxB/C/V/ZC/ZE, ispCLOCK, Power Manager/II, ProcessorPM
  • FPGA: Microsemi(Actel): ProASIC3, IGLOO, Fusion, ProASICplus, SmartFusion
  • FPGA: Lattice: MachXO, MachXO2, LatticeXP, LatticeXP2, ispXPGA
  • Dataman 848Pro2 Stand-Alone Production Programmer
    • Processor: Intel Core i5 2.9 GHz
    • Memory: 4 GB
    • Hard drive: 500 GB
    • Operating system: Windows Embedded 8.1 Industry Pro
    • Dimensions: 625 x 465 x 115mm (24.6 x 18.3 x 4.5inches)
    • Weight: 14.9Kg (32.85lbs)
    • Operating voltage: 100-240V
    • Power consumption: max. 300W active
  • Diagnostic POD for ZIF socket selftest of the programmer (x1)
  • Diagnostic POD for ISP connector selftest of the programmer (x1)
  • ISP cable (x8)
  • Anti-dust cover for ZIF socket (x8)
  • ESD wrist strap with cord and banana plug
  • User Manual
  • Software
  • Transport case
  • Optional range of adapters and socket converters also available


The Dataman 848Pro2 Stand-Alone Production Programmer comes with:

  • 30 Day Money Back Guarantee* - If you don't like it, send it back.
  • Three Year Guarantee - Three years parts and labour warranty, on the 848Pro2 stand-alone gang programmer.
  • Life-Time Technical Support - 848Pro2 technical support is available free via our website and telephone helpdesk for life.
  • Life-Time Software Updates - 848Pro2 software updates are available free via our website for life.



*Applies to orders from UK/US offices only.

   
  848Pro2
Type  
Universal  
Multi Socket  
Stand-Alone
Specialised  
   
Sockets  
1 x 48-pin  
4 x 48-pin  
8 x 48-pin
   
Device Support  
Number of Supported Devices 105,000+
Low Voltage Support
High Current/Voltage Legacy Support
   
Programming Modes  
Concurrent
Semi-Concurrent  
Fully Independant
   
Features  
Self Test
Insertion Test
ESD Protection
ISP Capability
Multi-Programmer Capability  
   
Dimensions/Weight  
Width (mm) 625
Depth (mm) 465
Height (mm) 115
Weight (Kg) 14.9
   
Warranty/Support  
Parts and Labour (Years) 3
Life-Time Technical Support
Life-Time Software Updates
   
Programming Speed (program/verify)  
Microchip 24FC128 00:02.3
ST M25P20 00:03.0
Intel QB25F640S33 00:30.7
SST SST39VF016Q 00:40.8
AMD Am29DL640G 00:24.0
Samsung K8P6415UQB 00:13.0
Samsung K9F1G08U0M 02:02.7
Microchip PIC18LF8720 00:11.0
Atmel AT89C51RD2 00:14.4